Dynamic characteristic of spur gear with flexible support of gearbox
Lei Zhang^{1} , Changzheng Chen^{2} , Jie Liu^{3} , Siyu Zhao^{4}
^{1, 2, 3, 4}Shenyang University of Technology, Shenyang, P. R. China
^{2}Corresponding author
Journal of Vibroengineering, Vol. 20, Issue 3, 2018, p. 15301543.
https://doi.org/10.21595/jve.2017.18721
Received 5 June 2017; received in revised form 24 August 2017; accepted 25 October 2017; published 15 May 2018
JVE Conferences
In this study, a nonlinear translationtorsion model of spur gear pair with flexible support of gearbox is proposed. The timevarying meshing stiffness, transmission error and backlash are considered in this model. Lagrange’s equations are used for establishing the mathematic model. The numerical method is presented for solutions of nonlinear differential equations. The effect of rotating speed and support stiffness of gearbox is analyzed. The numerical results show that the flexibility of the support of gearbox has a significant effect on the amplitudefrequency characteristic of the spur gear pair at low rotating speeds. The response shows flexibility while the support stiffness is smaller than the bearings and rigidity while the support stiffness is larger than the bearings. The maximum deformation of the driving gear bearings under the flexible support is generally greater than the one under rigid support.
Keywords: spur gear, nonlinear vibration, flexible support, dynamic response.
1. Introduction
Gear transmission system is one of the most important mechanisms used for motion and power transmission in industrial machinery, such as machine tool, automobile, wind turbine, etc. Many researchers have paid their attention to analyze the characteristics of gear systems by analytical methods, simulation technique and experimental methods. Most early researches focused on the mathematic modeling of a spur gear pair supported by flexible shaft and bearings, where gear torsional vibrations were the main concern [1, 2]. Both of lamped mass method and finite element method are used for establishing the dynamic model. Both of the numerical methods and approximate analytical methods are used for solving the analyzing the dynamic characteristics of spur gear pair.
Clearances including tooth backlash and clearance of bearings provide strongnonlinearity for the gear system and makes contributions to the vibration and noise of the gear system. In the early 1990s, Kahraman and Singh made parametric studies about bearing stiffness to meshing stiffness ratio, radial bearing preload to mean force ratio, etc. [3] and revealed interaction between timevarying meshing stiffness and backlash [4, 5] using both of the numerical method and harmonic balance method (HBM). Later in 2006, a torsional nonlinear dynamic model with 2degreeoffreedom was reduced to a dynamic model with singledegreeoffreedom and the incremental harmonic balance method (IHBM) was used for analyzing the torsional response of spur gear pair considering timevarying meshing stiffness, static transmission error and backlash [6]. Lassâad [7] investigated dynamics of a twostage gear system involving backlash and timedependent meshing stiffness. Chen [8] focused on the effects of the friction and dynamic backlash on the multidegree of freedom nonlinear dynamic gear transmission system, which incorporated time varying stiffness. Li [9] investigated the nonlinear dynamic characteristics of a gear pair system with dynamic backlash subjected to internal and external periodic excitations based on IHBM.
Friction force also provides strongnonlinearity for the geared system. Many scholars have studied the influence of friction on gear dynamics. Benedict and Kelley [10] analyzed the friction coefficient of gear meshing in a gear contact as simulated on a roller test machine. Howard [11] provided a simplified gear dynamic model aimed at exploring the effect of friction on the resultant gear case vibration. Effect of friction force on the multidegree of freedom nonlinear dynamic gear transmission system was also studied in reference [8]. Li [12] proposed a tribodynamics model which coupled a mixed elastohydrodynamic lubrication model for spur gear pairs. Ghosh [13] studied the instability due to parametric excitation from variable meshing stiffness in a gear pair system with the help of a sixdegreeoffreedom translationalrotational model to consider the contribution of tooth sliding friction. Zhou [14] developed a coupled lateraltorsional nonlinear dynamic model with 16degreeoffreedom (16DOF) of gearrotorbearing transmission system (GRBTS) to study the effect of friction coefficient and mead load on the dynamic response of the GRBTS.
Parameter excitations, such as timevarying meshing stiffness and gear transmission error, provide weaknonlinearity for the gear system. Many researchers have developed various mathematical models, such as analytical method [1518], finite element method [1922] and experimental method, to calculate the timevarying meshing stiffness [23, 24]. Transmission error is one of the most important internal excitation of spur gear pair and the major internal exaction of many previous models [36].
To the author’s knowledge, the effect of gearbox case was mostly neglected, and the support condition of the gearbox was assumed commonly to be rigid in the previous studies on spur gear dynamics. Therefore, for many mechanical equipment, such as wind turbines, the support condition of the gearbox is flexible. In these cases, the flexibility of gearbox support is nonnegligible. Thus, the dynamic model of spur gear pair with flexible support of gearbox is proposed in this paper. The dynamic model of gear pair with flexible support of gearbox will be proposed in Section 2. Numerical simulation results are provided to analyze the dynamic characteristics of the gear pair in Section 3. The conclusions will be given in Section 4.
2. Dynamic model of the spur gear pair
In this paper, some assumptions are presented to simplify the dynamic model: (a) the gearbox is reduced to a rigid body, (b) the timevarying meshing stiffness is approximated by Fourier function, (c) the effect of manufacturing error and assembly error is reduced to static transmission error which is defined in Fourier series, (d) the thermal deformation of the gear pair and friction forces at the gear meshing point are neglected, (e) the support of bearings is modeled by fixed stiffness spring and (f) both of the meshing damping and support damping are modeled by viscous damping.
Fig. 1. Dynamic model of a spur gear pair with flexible support of gearbox
Fig. 1 shows a dynamic model of a spur gear pair with flexible support of gearbox. As shown in Fig. 1, each component has three degrees of freedom, two translational vibration degrees of freedom and one torsional vibration degree of freedom. The timevarying meshing stiffness is expressed [25]:
where, ${k}_{m}\left(t\right)$ is the timevarying meshing stiffness which consists of mean component ${k}_{m}^{0}$ and periodic components with amplitude coefficients ${k}_{m}^{n}$ and phase angles ${\phi}_{k}^{n}$. In this paper, ${\omega}_{m}$ represents the meshing frequency of the spur gear pair.
Like the definition of timevarying meshing stiffness, the transmission error is also defined in Fourier series [25] as shown in Eq. (2):
Here, ${e}_{m}\left(t\right)$ represents the static transmission error which consists of periodic components with amplitudes ${e}_{m}^{n}$ and phase angle ${\phi}_{e}^{n}$, respectively.
The comprehensive deformation $\delta \left(t\right)$ between the driving gear and driven gear along the meshing line is expressed:
where $\alpha $ is the pressure angle of the driving gear and driven gear; ${r}_{1}$ and ${r}_{2}$ are base radii of driving gear and driven gear, respectively.
Considering the effect of backlash, the nonlinearity function of the comprehensive deformation is expressed:
where $b$ represents the halfbacklash value. The meshing force, ${f}_{m}$, is expressed:
where, ${c}_{m}$ is the meshing damping which is defined as a constant. In this system, the deformation of bearings and support springs is as follows:
where ${\delta}_{x}^{1}$ and ${\delta}_{y}^{1}$ represent the relative displacement between driving gear bearings and gearbox in ${x}_{1}$ direction and ${y}_{1}$ direction, ${\delta}_{x}^{2}$ and ${\delta}_{y}^{2}$ represent the relative displacement between driven gear bearings and gearbox in ${x}_{2}$ direction and ${y}_{2}$ direction, ${\delta}_{Mx}^{L}$ and ${\delta}_{Mx}^{R}$ represent the deformation of left and right supporting springs of gearbox in ${x}_{M}$ direction and ${\delta}_{My}^{L}$ and ${\delta}_{My}^{R}$ represent the deformation of left and right supporting springs of gearbox in ${y}_{M}$ direction. The symbol ${l}_{o}$ represents the distance between the rotary center of driving gear and driven gear and ${l}_{x}$ is the distance between the support spring of gearbox in ${y}_{M}$ direction and the mass center of the gearbox. We can obtain:
where, $T$ represents the kinetic energy, $U$ is the potential energy of bearings and flexible supports of the gearbox and $R$ is the dissipation function of bearing damping and flexible support damping. The symbols, ${m}_{1}$, ${m}_{2}$ and ${m}_{M}$ are the masses of driving gear, driven gear and gearbox and ${J}_{1}$, ${J}_{2}$ and ${J}_{M}$ are the moment of inertia of driving gear, driven gear and gearbox. The symbols, ${k}_{1}$, ${k}_{2}$, ${k}_{Mx}$ and ${k}_{My}$, represent the supporting stiffness of driving gear bearings, driven gear bearings and supporting springs of gearbox and ${c}_{1}$, ${c}_{2}$, ${c}_{Mx}$ and ${c}_{My}$ are the corresponding damping.
Using the Lagrange’s equations, the differential equations of motion of the system is established:
where ${\mathbf{Q}}_{f}$ and is the generalized force and ${\mathbf{q}}_{f}$ is the generalized coordinate which are defined in Eq. (13):
In Eq. (13), ${T}_{d}$ is the driving torque and ${T}_{l}$ is the load torque. The mathematic model of the spur gear pair with flexible support of gearbox is expressed as:
3. Numerical simulation and result discussion
The parameters of the spur gear pair are shown in Table 1. In this paper, $N=$ 1 is applied to Eq. (1) and Eq. (5) and the damping coefficient of flexible support is $\xi =$ 0.15. The damping of flexible support is written as:
where $j=[x,y]$. The NewMark$\beta $ method is used for solving Eq. (14). For a better comparison, a dynamic model of spur gear pair under rigid support condition is giving in Appendix B. The effect of rotating speed on the dynamic response will be discussed in section 3.1, the effect of support stiffness will be discussed in section 3.2 and the bearing deformation will be discussed in section 3.3.
Table 1. Parameters of the gear pair
Parameter

Value

Parameter

Value

Pressure angle $\alpha $

20°

Mass ${m}_{1}$/${m}_{2}$

1.53/3.01 kg

Mass ${m}_{M}$

19.87 kg

Moment of inertia ${J}_{1}$/${J}_{2}$

0.041/0.079 kg·m^{2}

Moment of inertia ${J}_{M}$

0.35 kg·m^{2}

Stiffness of bearings ${k}_{1}$/${k}_{2}$

2/2×10^{8} N·m^{1}

Meshing stiffness ${k}_{m}^{0}$

3.2×10^{8} N·m^{1}

Meshing stiffness coefficient ${k}_{m}^{1}$

0.3

Phase angle of meshing stiffness coefficient ${\phi}_{k}^{1}$

0

Damping of bearings ${c}_{1}$/${c}_{2}$

1800/1800 N·s·m^{1}

Meshing damping ${c}_{m}$

2000 N·s·m^{1}

Transmission error ${e}_{m}^{1}$

1×10^{5} m

Phase angle of the transmission error ${\phi}_{e}^{1}$

0

Halfbacklash value $b$

1×10^{5} m

Driving torque ${T}_{d}$

110 N·m

Loading torque ${T}_{l}$

150 N·m

3.1. Effect of rotating speed
In this section, the stiffness of flexible support is supposed to be ${k}_{Mx}=$ 2.5×10^{5} N·m^{1} and ${k}_{My}=$ 2.5×10^{5} N·m^{1}. Taking the rotating speed of the driving gear as a control parameter, both of the amplitudefrequency response curve of the driving gear in ${y}_{1}$direction under flexible support condition and rigid support condition are shown in Fig. 2.
Under rigid support condition, two significant peaks at 1180 r·min^{1} and 1730 r·min^{1} appear while the rotating speed is less 3100 r·min^{1}. As the speed increases, there is a jump at rotating speed of 3140 r·min^{1}. With the further increase of the rotating speed, another four jumps appear at $n=$ 4650 r·min^{1}, $n=$ 4730 r·min^{1}, $n=$ 4930 r·min^{1} and $n=$ 5290 r·min^{1}. The response beyond 4650 r·min^{1} becomes strongly nonlinear and consists of periodic, multiperiodic and chaotic motion. Under flexible support condition, it is obvious that one more peak appears at rotating speed of 480 r·min^{1}. The other two peaks appear at rotating speed of 1290 r·min^{1 }and 1900 r·min^{1} of which the rotating speeds are slightly higher than the corresponding ones under rigid support condition. Several jumps appear at rotating speed of 4670 r·min^{1}, 4810 r·min^{1}, 4880 r·min^{1} and 5310 r·min^{1} as the rotating speed increases. With the further increase of the rotating speed, the response beyond 4670 r·min^{1} also becomes strongly nonlinear and consists of period, multiperiodic and chaotic motion.
Fig. 2. Amplitudefrequency response curve the driving gear in ${y}_{1}$ direction
The waterfall plot of displacement of driving gear in ${y}_{1}$direction under flexible support condition is shown in Fig. 3(a) and the corresponding bifurcation diagram is shown in Fig. 3(c). The meshing frequency (${f}_{m}$) is the dominant response, the amplitude of 2meshing frequency (2${f}_{m}$) is relatively small, and the bifurcation diagram shows that the response is periodic motion in the range of $n\in [300,4650]$. The meshing frequency (${f}_{m}$) is the dominant response, nonharmonic frequency components appear in the system response and the response is chaotic motion in the range of $n\in (4650,4990]$. Multiplication frequency components, such as ${f}_{m}$/3, 2${f}_{m}$/3, ${f}_{m}$, 2${f}_{m}$, etc. appear and the response is 3T periodic motion in the range of $n\in (4990,5310]$. With the increase of rotating speed, the 3T periodic motion is replaced by periodic motion, the meshing frequency is the dominant response and the amplitude of 2${f}_{m}$ is obvious in the range of $n\in (5310,5610]$. With the further increase of rotating speed, multiplication frequency components, such as ${f}_{m}$/2, ${f}_{m}$, 2${f}_{m}$, etc. appear and the response is replaced by 2T periodic motion in the range of $n\in (5610,6000]$. In short, the spur gear pair under flexible support condition undergoes periodic motion, chaotic motion and $N$T periodic motion.
The waterfall plot of displacement of driving gear in ${y}_{1}$direction under rigid support condition shown in Fig. 3(b) and the corresponding bifurcation diagram shown in Fig. 3(d) are similar to the ones under flexible support condition. The spur gear pair under rigid support condition also undergoes periodic motion, chaotic motion and NT periodic motion. The gear system exhibits periodic motion in ${y}_{1}$direction and the frequency components about ${f}_{m}$ and 2${f}_{m}$ appear in the range of $n\in [300,4640]\cup (5400,5460]$. The response is replaced by chaotic motion and the frequency components about meshing frequency and some nonharmonic frequency are obvious in the range of $n\in (4640,4980]$. The frequency components about ${f}_{m}$/3, 2${f}_{m}$/3, ${f}_{m}$, 2${f}_{m}$, etc. appear and the response is 3T periodic motion in the range of $n\in (4980,5400]$. While the rotating speed is beyond 5460 r·min^{1}, the spur gear pair exhibits 2T periodic motion in ${y}_{1}$ direction and frequency components about ${f}_{m}$/2, ${f}_{m}$, 2${f}_{m}$, etc. are obvious.
Fig. 3. Waterfall plots and bifurcation diagrams of driving gear in ${y}_{1}$ direction: a) waterfall plot under flexible support condition, b) waterfall plot under rigid support condition, c) bifurcation diagram under flexible support condition, d) bifurcation diagram under rigid support condition
a)
b)
c)
d)
For a better clarity, the dynamic response of the spur gear pair under flexible support condition will be analyzed at five rotating speeds of $n=$ 1500 r·min^{1}, $n=$ 4900 r·min^{1}, $n=$ 5300 r·min^{1}, $n=$ 5500 r·min^{1} and $n=$ 5900 r·min^{1}. Here, the time history is shown in Fig. 3(a), FFT spectrum is shown in Fig. 3(b), the phase plane is shown in Fig. 3(c) and the Poincaré map is shown in Fig. 3(d). The response at $n=$ 1500 r·min^{1} is illustrated in Fig. 4. The time history indicates that the response is periodic. The spectrum illustrates that the meshing frequency (${f}_{m}$) is the dominant response and the amplitude of 2meshing frequency (2${f}_{m}$) is relatively small. The phase plane and the Poincaré map indicate that response at $n=$ 1500 r·min^{1} is periodic motion. The response at $n=$ 4900 r·min^{1} is shown in Fig. 5. The time history shows that there is no obvious periodicity.
Fig. 4. Periodic motion of driving gear in ${y}_{1}$ direction at $n=$ 1500 r·min^{1} under flexible support condition: a) time history, b) FFT spectrum, c) phase plane, d) Poincaré map
a)
b)
c)
d)
Fig. 5. Chaotic motion of driving gear in ${y}_{1}$direction at $n=$ 4900 r·min^{1} under flexible support condition: a) time history, b) FFT spectrum, c) phase plane, d) Poincaré map
a)
b)
c)
d)
As shown in the spectrum, ${f}_{m}$ is the dominant response and nonharmonic frequency components, such as 0.26 ${f}_{m}$, 0.37${f}_{m}$, 0.74${f}_{m}$, 1.37${f}_{m}$ and 1.63${f}_{m}$, etc., appear. The phase plane and the Poincaré map indicate that response at $n=$ 4900 r·min^{1} is chaotic motion. The response at $n=$ 5300 r·min^{1} is shown in Fig. 6. The time history indicates that the response is triply period. The spectrum shows that 2${f}_{m}$/3 is the dominant response and amplitudes at ${f}_{m}$/3, ${f}_{m}$, 4${f}_{m}$/3, 5${f}_{m}$/3, 2${f}_{m}$ and 8${f}_{m}$/3 are obvious. The phase plane and the Poincaré map indicate that response at $n=$ 5300 r·min^{1} is 3T periodic motion. The response at $n=$ 5500 r·min^{1} is shown in Fig. 7. Like the response at $n=$ 1500 r·min^{1}, the response at $n=$ 5500 r·min^{1} is also period as the time history shows. The spectrum shows that component at ${f}_{m}$ is the dominant response and the amplitude at 2${f}_{m}$ is relatively small. The phase plane and Poincaré map indicate that the response at $n=$ 5500 r·min^{1} is also periodic motion. As the rotating speed increases to $n=$ 5900 r·min^{1}, the dynamic response is shown in Fig. 8. The time history shows that the response is doubly period. The spectrum illustrates that the component at ${f}_{m}$ is the dominant response and amplitudes at ${f}_{m}$/2, ${f}_{m}$, 3${f}_{m}$/2, 2${f}_{m}$, 3${f}_{m}$, etc. are obvious. The phase plane and Poincaré map indicates that the response at $n=$ 5900 r·min^{1} is 2T periodic motion.
Fig. 6. 3T periodic motion of driving gear in ${y}_{1}$direction at $n=$ 5300 r·min^{1} under flexible support condition: a) time history, b) FFT spectrum, c) phase plane, d) Poincaré map
a)
b)
c)
d)
Fig. 7. Periodic motion of driving gear in ${y}_{1}$direction at $n=$ 5500 r·min^{1} under flexible support condition: a) time history, b) FFT spectrum, c) phase plane, d) Poincaré map
a)
b)
c)
d)
Fig. 8. 2T periodic motion of driving gear in ${y}_{1}$direction at $n=$ 5900 r·min^{1} under flexible support condition: a) time history, b) FFT spectrum, c) phase plane, d) Poincaré map
a)
b)
c)
d)
3.2. Effect of support stiffness of gearbox
In this section, the effect of support stiffness of gearbox and rotating speed on the dynamic response is discussed. The support stiffness of gearbox in ${x}_{M}$ direction is supposed to be equal to the one in ${y}_{M}$ direction. Here, the rotating speed $n$ and support stiffness of gearbox ${k}_{My}$ are treated as control parameters varying in range of $n\in [300,6000]$ and ${k}_{My}\in [{10}^{3},{10}^{12}]$. The amplitudefrequencystiffness response map is shown in Fig. 9.
The effect of support stiffness of gearbox on the response is quite evident as the rotating speed varying in range of $n\in [300,3100]$. The first crest appears at $n=$ 480 r·min^{1}. The crest at $n=$ 480 r·min^{1} gradually decreases and moves to the right of the figure along the black line. Another two crests at $n=$ 1290 r·min^{1} and $n=$ 1900 r·min^{1} appear as the support stiffness is blow the black line and two crests at $n=$ 1180 r·min^{1} and $n=$ 1730 r·min^{1} appear as the support stiffness is above the black line while the rotating speed is less than 3100 r·min^{1}. With the increase of rotating speed, the support stiffness of gearbox has little effect on the dynamic response in ${y}_{1}$ direction in the range of $n\in [3100,4400]$. When the rotating speed is beyond 4400 r·min^{1}, the support stiffness of gearbox has some irregular effect on the dynamic response in ${y}_{1}$ direction. Compared to the amplitudefrequency cure of the driving gear in ${y}_{1}$ direction shown in Fig. 2, it is obvious that the response of driving gear in ${y}_{1}$ direction under flexible support condition with large support stiffness is more similar to the one under rigid support condition.
Fig. 9. Amplitudefrequencystiffness response map of the driving gear in ${y}_{1}$ direction
3.3. Bearing deformation
For many mechanical equipment, the failure often occurs in the bearings. Thus, the bearing deformation of the driving gear bearings under flexible support condition and the one under rigid support condition are compared in this section.
The bearing deformation of the driving gear bearings under rigid support condition, ${\delta}_{r}^{i}\left(t\right)$, is expressed:
The bearing deformation of the driving gear under flexible support condition, ${\delta}_{f}^{i}\left(t\right)$, is expressed:
The maximum relative displacement coefficient, $\eta $, is defined as:
Fig. 10. Bearing deformation of the driving gear bearings: a) deformationfrequency response cure under rigid support condition, b) deformationfrequencystiffness response map under flexible support condition, c) $\eta $ frequencystiffness response map
a)
b)
c)
The deformationfrequency response cure of the driving gear is shown in Fig. 10(a), the deformationfrequencystiffness response map of the driving gear is shown in Fig. 10(b) and the $\eta $ frequencystiffness response map of the driving gear bearings is shown in Fig. 10(c). Comparing Fig. 10(a) with Fig. 2, the deformationfrequency response cure is similar to the amplitudefrequency response curve of the spur gear pair. Comparing Fig. 10(b) with Fig. 9, it is obvious that the ${\delta}_{f}$ frequencystiffness response map of the driving gear bearings is similar to the amplitudefrequencystiffness response map of the driving gear in $y$ direction.
The difference between these two figures is that the crest along the black line in Fig. 10(b) is inconspicuous. Fig. 10(c) shows the $\eta $ frequencystiffness response map of the driving gear bearings, which represents the quantitative comparison between the bearing deformation of the driving gear under flexible support condition and the bearing deformation of the driving gear under rigid support condition. This map is divided into several different areas for a better clarity. Area A represents the maximum relative displacement coefficient with large support stiffness. The coefficient $\eta $ is generally close to zero in area A, which means that the bearing deformation of driving gear bearings with large support stiffness is close to the deformation of driving gear under rigid support condition. In area B, D, F and H, the coefficient $\eta $ is generally larger than zero, which means the bearing deformation of driving gear bearings is larger than the one under rigid support condition. Furthermore, the deformation of driving gear bearings in the range as shown in area D is much larger than the corresponding one under rigid support condition as the coefficient $\eta $ is much larger than zero. In area C, E and G, the coefficient $\eta $ is less than zero, which means the bearing deformation under flexible support condition in these areas is smaller than the one under rigid support condition.
In short, it is obvious that the coefficient $\eta $ is generally greater than zero, which means the maximum deformation of the driving gear bearings under the flexible support is generally greater than the one under rigid support.
4. Conclusions
A lumped parameter dynamic model considering the flexibility of the support of the gearbox is proposed in this study. The nonlinear equations of motion are obtained via Lagrange’s equation. The NewMark method is adopted to investigate the nonlinear behavior of gear transmission system. The effects of rotating speed and support stiffness of gearbox are considering to be analyzed. The numerical simulation shows that the flexible support of the gearbox significantly changes the amplitudefrequency response curve of the gear transmission system at low rotating speed. The response shows flexibility while the support stiffness is smaller than the bearings and rigidity while the support stiffness is larger than the bearings. The maximum deformation of the driving gear bearings under the flexible support is generally greater than the one under rigid support.
Acknowledgements
The authors would like to gratefully acknowledge the National Natural Science Foundation of China (Grant No. 51675350 and 51575361), and the Natural Science Foundation of LiaoNing (201602544) for the financial support for this study.
References
 Özgüven H. N., Houser D. R. Mathematical models used in gear dynamics – a review. Journal of Sound and Vibration, Vol. 121, Issue 3, 1988, p. 383411. [Publisher]
 Wang J., Li R., Peng X. Survey of nonlinear vibration of gear transmission systems. Applied Mechanics Reviews, Vol. 121, Issue 3, 1988, p. 383411. [Search CrossRef]
 Kahraman A., Singh R. Interactions between timevarying meshing stiffness and clearance nonlinearities in a geared system. Journal of Sound and Vibration, Vol. 146, Issue 1, 1991, p. 135156. [Publisher]
 Kahraman A., Singh R. Nonlinear dynamics of a spur gear pair. Journal of Sound and Vibration, Vol. 142, Issue 1, 1990, p. 4975. [Publisher]
 Kahraman A., Singh R. Nonlinear dynamics of a geared rotorbearing system with multiple clearances. Journal of Sound and Vibration, Vol. 144, Issue 3, 1991, p. 469506. [Publisher]
 Shen Y., Yang S., Liu X. Nonlinear dynamics of a spur gear pair with timevarying stiffness and backlash based on incremental harmonic balance method. International Journal of Mechanical Sciences, Vol. 48, Issue 11, 2006, p. 12561263. [Publisher]
 Walha L., Fakhfakh T., Haddar M. Nonlinear dynamics of a twostage gear system with meshing stiffness fluctuation, bearing flexibility and backlash. Mechanism and Machine Theory, Vol. 44, Issue 5, 2009, p. 10581069. [Publisher]
 Siyu C., Jinyuan T., Caiwang L., Qibo W. Nonlinear dynamic characteristics of geared rotor bearing systems with dynamic backlash and friction. Mechanism and Machine Theory, Vol. 46, Issue 6, 2011, p. 466478. [Publisher]
 Li Y., Chen X., Wang X. Nonlinear dynamics of gear pair with dynamic backlash subjected to combined internal and external periodic excitations. Journal of Vibration and Control, Vol. 8, Issue 6, 2014, p. 111. [Search CrossRef]
 Benedict G. H., Kelley B. W. Instantaneous coefficients of gear tooth friction. ASLE Transactions, Vol. 4, Issue 1, 1961, p. 5970. [Publisher]
 Howard I., Jia S., Wang J. The dynamic modelling of a spur gear in meshing including friction and a crack. Mechanical Systems and Signal Processing, Vol. 15, Issue 5, 2001, p. 831853. [Publisher]
 Li S., Kahraman A. A tribodynamic model of a spur gear pair. Journal of Sound and Vibration, Vol. 332, Issue 20, 2013, p. 49634978. [Publisher]
 Ghosh S. S., Chakraborty G. Parametric instability of a multidegreeoffreedom spur gear system with friction. Journal of Sound and Vibration, Vol. 332, 2015, p. 236253. [Publisher]
 Zhou S., Song G., Sun M., et al. Nonlinear dynamic response analysis on gearrotorbearing transmission system. Journal of Vibration and Control, 2016, https://doi.org/10.1177/1077546316667178. [Search CrossRef]
 Mohammed O. D., Rantatalo M., Aidanpää J. O., et al. Vibration signal analysis for gear fault diagnosis with various crack progression scenarios. Mechanical Systems and Signal Processing, Vol. 41, Issue 1, 2013, p. 176195. [Publisher]
 Mohammed O. D., Rantatalo M., Aidanpää J. O. Dynamic modelling of a onestage spur gear system and vibrationbased tooth crack detection analysis. Mechanical Systems and Signal Processing, Vol. 54, 2015, p. 293305. [Publisher]
 Pandya Y., Parey A. Simulation of crack propagation in spur gear tooth for different gear parameter and its influence on meshing stiffness. Engineering Failure Analysis, Vol. 30, 2013, p. 124137. [Publisher]
 Wu S., Zuo M. J., Parey A. Simulation of spur gear dynamics and estimation of fault growth. Journal of Sound and Vibration, Vol. 317, Issue 3, 2008, p. 608624. [Publisher]
 Ma H., Pang X., Zeng J., et al. Effects of gear crack propagation paths on vibration responses of the perforated gear system. Mechanical Systems and Signal Processing, Vol. 62, 2015, p. 113128. [Publisher]
 Chaari F., Fakhfakh T., Haddar M. Analytical modelling of spur gear tooth crack and influence on gear meshing stiffness. European Journal of MechanicsA/Solids, Vol. 28, Issue 3, 2009, p. 461468. [Publisher]
 Ma H., Song R., Pang X., et al. Timevarying meshing stiffness calculation of cracked spur gears. Engineering Failure Analysis, Vol. 44, 2014, p. 179194. [Publisher]
 Raghuwanshi N. K., Parey A. Effect of backside contact on meshing stiffness of spur gear pair by finite element method. Procedia Engineering, Vol. 173, 2017, p. 15381543. [Publisher]
 Pandya Y., Parey A. Experimental investigation of spur gear tooth meshing stiffness in the presence of crack using photoelasticity technique. Engineering Failure Analysis, Vol. 34, 2013, p. 488500. [Publisher]
 Raghuwanshi N. K., Parey A. Experimental measurement of gear meshing stiffness of cracked spur gear by strain gauge technique. Measurement, Vol. 86, 2016, p. 266275. [Publisher]
 Liu J., Wang S., Zhou S., et al. Nonlinear behavior of a spur gear pair transmission system with backlash. Journal of Vibroengineering, Vol. 16, Issue 8, 2014, p. 39223938. [Search CrossRef]
Cited By
IOP Conference Series: Materials Science and Engineering
V I Skel

2021

International Journal of Rotating Machinery
Jie Liu, Chengye Wang, Wenchao Wu

2020
